<?xml version="1.0" encoding="UTF-8"?><rss version="2.0"
	xmlns:content="http://purl.org/rss/1.0/modules/content/"
	xmlns:wfw="http://wellformedweb.org/CommentAPI/"
	xmlns:dc="http://purl.org/dc/elements/1.1/"
	xmlns:atom="http://www.w3.org/2005/Atom"
	xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
	xmlns:slash="http://purl.org/rss/1.0/modules/slash/"
	>

<channel>
	<title>initial settings &#8211; Sugitama-Lab.</title>
	<atom:link href="https://sugitama-lab.tech/en/tag/initial-settings-en/feed/" rel="self" type="application/rss+xml" />
	<link>https://sugitama-lab.tech</link>
	<description>Handy SOLIDWORKS tips, explained</description>
	<lastBuildDate>Tue, 10 Nov 2026 10:03:41 +0000</lastBuildDate>
	<language>en-US</language>
	<sy:updatePeriod>
	hourly	</sy:updatePeriod>
	<sy:updateFrequency>
	1	</sy:updateFrequency>
	

<image>
	<url>https://sugitama-lab.tech/wp-content/uploads/2021/12/cropped-illust_Tool_icon-32x32.png</url>
	<title>initial settings &#8211; Sugitama-Lab.</title>
	<link>https://sugitama-lab.tech</link>
	<width>32</width>
	<height>32</height>
</image> 
<site xmlns="com-wordpress:feed-additions:1">205154850</site>	<item>
		<title>SOLIDWORKS System Options for Better Usability: Recommended Settings</title>
		<link>https://sugitama-lab.tech/en/solidworks-system-options-usability/</link>
					<comments>https://sugitama-lab.tech/en/solidworks-system-options-usability/#respond</comments>
		
		<dc:creator><![CDATA[sugitama]]></dc:creator>
		<pubDate>Mon, 09 Nov 2026 22:42:01 +0000</pubDate>
				<category><![CDATA[settings]]></category>
		<category><![CDATA[business efficiency]]></category>
		<category><![CDATA[for beginners]]></category>
		<category><![CDATA[initial settings]]></category>
		<category><![CDATA[mistake prevention]]></category>
		<category><![CDATA[speed & performance]]></category>
		<guid isPermaLink="false">https://sugitama-lab.tech/?p=3690</guid>

					<description><![CDATA[Recommended SOLIDWORKS System Options for better usability: settings that cut down on operations and prevent input mistakes, with the pros and cons of the ones that trade off against speed.]]></description>
										<content:encoded><![CDATA[
<p class="wp-block-paragraph">Before you start designing in SOLIDWORKS, I recommend setting up the System Options.</p>



<p class="wp-block-paragraph">A well-prepared environment lets you skip some steps, avoid mistakes, and reduce the strain on you. In short, it makes design work more efficient.</p>



<p class="wp-block-paragraph">This article explains the SOLIDWORKS System Options, focusing on the settings that improve usability.</p>



<p class="wp-block-paragraph">The settings are simple, and you can finish them in about five minutes. I hope you will give them a try.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">This article recommends settings from two angles: cutting down on the number of operations, and preventing input mistakes and missed checks.</p>



<p class="wp-block-paragraph">A few of the settings trade off against processing speed, so I list their pros and cons.</p>
</div></div>



<p class="wp-block-paragraph">If you want to make SOLIDWORKS itself run lighter, see the article below.</p>



<p class="wp-block-paragraph">&nbsp;&nbsp;» <a href="https://sugitama-lab.tech/en/solidworks-performance-optimize/"><strong>SOLIDWORKS Performance Optimization: Settings to Make SOLIDWORKS Run Faster</strong></a></p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">What Are System Options?</h2>



<p class="wp-block-paragraph">System Options are settings that apply every time you use SOLIDWORKS.</p>



<p class="wp-block-paragraph">With them, you can switch many of the features, behaviors, and tools built into SOLIDWORKS on or off.</p>



<p class="wp-block-paragraph">If you tune the System Options well, you get benefits like these:</p>



<ul class="wp-block-list">
<li>Simpler operations mean less mouse movement, which saves working time.</li>



<li>It is easier to see what changed and what you are editing, which helps prevent mistakes.</li>



<li>Fewer missed checks and careless mistakes make your work more stable.</li>
</ul>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">When your System Options are tuned, there is less stress in your work, and design becomes more enjoyable.</p>
</div></div>



<h2 class="wp-block-heading">Setting Up System Options</h2>



<p class="wp-block-paragraph">To open the System Options, choose <strong>Tools &gt; Options</strong>.</p>



<figure class="wp-block-image size-large"><img fetchpriority="high" decoding="async" width="285" height="990" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/perf-sysopt-open-menu.png" alt="The Tools menu with Options selected" class="wp-image-3560" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/perf-sysopt-open-menu.png 285w, https://sugitama-lab.tech/wp-content/uploads/2026/11/perf-sysopt-open-menu-86x300.png 86w" sizes="(max-width: 285px) 100vw, 285px" /></figure>



<p class="wp-block-paragraph">&nbsp;</p>



<p class="wp-block-paragraph">Below are my recommended settings for better usability.</p>



<p class="is-style-supplement-normal wp-block-paragraph">Depending on your version of SOLIDWORKS, some of the options in this article may not exist, or their names and positions may differ. If you cannot find an item, you can simply skip it.</p>



<p class="wp-block-paragraph"><strong>The settings in this article put usability (ease of work and accuracy) first.</strong></p>



<p class="wp-block-paragraph">Some settings improve usability when you switch them on or off (or choose a particular value), but they make processing take longer, which can lower your efficiency overall. I mark those with <strong>[Your call]</strong> at the start of the item, and explain the trade-off.</p>



<p class="wp-block-paragraph">If you would rather give up some convenience for faster processing, see this article instead:</p>



<p class="wp-block-paragraph">&nbsp;&nbsp;» <a href="https://sugitama-lab.tech/en/solidworks-performance-optimize/"><strong>SOLIDWORKS Performance Optimization: Settings to Make SOLIDWORKS Run Faster</strong></a></p>



<p class="wp-block-paragraph">There is no single right answer. Decide based on the size of your models, the specs of your PC, and your own priorities.</p>



<h3 class="wp-block-heading">System Options &gt; General</h3>



<figure class="wp-block-image size-full"><img decoding="async" width="1323" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general.png" alt="System Options, General page" class="wp-image-3561" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general.png 1323w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general-300x151.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general-1024x517.png 1024w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general-768x388.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-general-485x245.png 485w" sizes="(max-width: 1323px) 100vw, 1323px" /></figure>



<ol class="wp-block-list">
<li><strong>Select &#8220;Input dimension value&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When this is selected, a box for typing the dimension value appears as soon as you place a dimension (SOLIDWORKS calls it the Modify box).</p>



<p class="wp-block-paragraph">You can enter the value right after placing the dimension, which makes the work more efficient.</p>



<ol start="2" class="wp-block-list">
<li><strong>Select &#8220;Automatically edit macro after recording&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">The Visual Basic editor opens right after you record a macro, so you can edit it immediately.</p>



<p class="wp-block-paragraph">When you create a macro, the main flow is to record it and then edit the VBA, so selecting this makes macro editing smoother.</p>



<ol start="3" class="wp-block-list">
<li><strong>Clear &#8220;Enable sounds for SOLIDWORKS events&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Do the notification sounds that play with every operation bother you?</p>



<p class="wp-block-paragraph">Event sounds are not essential, so turning them off helps you stay focused without being distracted by extra noise.</p>



<ol start="4" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Show thumbnail graphics in Windows Explorer&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">You can check a file’s shape from its thumbnail in Windows Explorer without opening the file.</p>



<p class="wp-block-paragraph">In exchange, SOLIDWORKS has to generate and display the thumbnails, which can make the display slower.</p>



<h3 class="wp-block-heading">System Options &gt; Drawings</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings.png" alt="System Options, Drawings page" class="wp-image-3562" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="5" class="wp-block-list">
<li><strong>Clear &#8220;Disable note/dimension inference&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you place a note or dimension, SOLIDWORKS shows guide lines that line it up horizontally or vertically with the notes and dimensions already on the sheet.</p>



<p class="wp-block-paragraph">This makes it easier to produce a neat-looking drawing.</p>



<ol start="6" class="wp-block-list">
<li><strong>Select &#8220;Print out-of-sync water mark&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">If a drawing has not been updated to match its 3D model, a watermark saying so is printed on the drawing.</p>



<p class="wp-block-paragraph">This helps you avoid issuing a drawing that no longer matches the model without noticing.</p>



<ol start="7" class="wp-block-list">
<li><strong>Clear &#8220;Reduce spacing when dimensions are deleted or edited (add or change tolerance, text etc…)&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">This stops other dimensions from moving on their own when you delete or edit a dimension on the drawing.</p>



<ol start="8" class="wp-block-list">
<li><strong>Select &#8220;Reuse view letters from deleted auxiliary, detail, and section views&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Suppose you have &#8220;Detail A&#8221; and &#8220;Detail B&#8221;, delete &#8220;Detail A&#8221;, and then create a new detail view. With this setting off, the new view gets the next letter, &#8220;Detail C&#8221;, and the lettering ends up with gaps that make the drawing harder to read.</p>



<p class="wp-block-paragraph">With the setting on, the free letter &#8220;A&#8221; is used again, so the labels run in order with no gaps.</p>



<h3 class="wp-block-heading">System Options &gt; Drawings &gt; Performance</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-performance.png" alt="System Options, Drawings, Performance page" class="wp-image-3563" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-performance.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-performance-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-performance-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-drawings-performance-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="9" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Allow auto-update when opening drawings&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you open a drawing, changes made to the model are reflected automatically. This helps you avoid the mistake of forgetting to update and issuing a drawing whose shape differs from the 3D model.</p>



<p class="wp-block-paragraph">On the other hand, an update always runs when you open the drawing, so opening files takes longer.</p>



<h3 class="wp-block-heading">System Options &gt; Colors</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="676" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-colors.png" alt="System Options, Colors page" class="wp-image-3685" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-colors.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-colors-300x230.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-colors-768x590.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-colors-485x373.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="10" class="wp-block-list">
<li><strong>Select &#8220;Use specified color for changed drawing dimensions on open&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">You can see the design changes at a glance, even if the drawing and the model were not open at the same time.</p>



<p class="wp-block-paragraph">If you change and save the model while the drawing is closed, and then open the drawing, the changed dimensions are shown in the specified color. (If you hover over one, you can also see its previous value.)</p>



<p class="wp-block-paragraph">When you save the drawing and reopen it, the dimensions return to their normal color.</p>



<ol start="11" class="wp-block-list">
<li><strong>Change the background to your liking</strong></li>
</ol>



<p class="wp-block-paragraph">The <strong>Background</strong> list lets you choose how light or dark the screen is.</p>



<p class="wp-block-paragraph">A change in screen brightness can help reduce eye strain during long working hours. Try it and set what suits you.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">When changed dimensions are easy to spot, you are less likely to make mistakes or miss a check. Item 11 is purely a matter of taste, so any choice is fine.</p>
</div></div>



<h3 class="wp-block-heading">System Options &gt; Sketch</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="676" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-sketch.png" alt="System Options, Sketch page" class="wp-image-3686" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-sketch.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-sketch-300x230.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-sketch-768x590.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-sketch-485x373.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="12" class="wp-block-list">
<li><strong>Select &#8220;Auto-rotate view normal to sketch plane on sketch creation and sketch edit&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">The view turns automatically so that you look straight at the sketch plane, which makes planar sketching easier.</p>



<ol start="13" class="wp-block-list">
<li><strong>Clear &#8220;Use fully defined sketches&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When this is selected, you cannot exit a sketch until its dimensions and relations are fully defined.</p>



<p class="wp-block-paragraph">That helps you avoid forgetting to fully define a sketch (black lines). But in real work there are times when you want to leave a sketch Under Defined (blue lines), so I clear this option.</p>



<ol start="14" class="wp-block-list">
<li><strong>Select &#8220;Scale sketch on first dimension creation&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you add the first dimension to a rough sketch, the whole sketch is scaled to match that dimension value.</p>



<p class="wp-block-paragraph">With the option cleared, entering the first dimension changes only that part, and the proportions against the rest of the sketch can break and distort the shape.</p>



<p class="wp-block-paragraph">With it selected, you can draw the shape first and then set the size all at once with the first dimension.</p>



<ol start="15" class="wp-block-list">
<li><strong>Select &#8220;Enable on screen numeric input on entity creation&#8221;</strong></li>



<li><strong>Select &#8220;Create dimension only when value is entered&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">These two settings go together. With them selected, you can enter a dimension and set its value while you are still drawing the sketch.</p>



<p class="wp-block-paragraph">Normally you draw a line, add a dimension with Smart Dimension, and then type the value. With these settings you can enter the dimension as you draw the line, which shortens sketching time.</p>



<ol start="17" class="wp-block-list">
<li><strong>Select &#8220;Preview sketch dimension when selected&#8221; (available in SOLIDWORKS 2024 and later)</strong></li>
</ol>



<p class="wp-block-paragraph">You do not need a dimension command: just select a sketch entity, and a preview of its dimension appears that you can click to type a value.</p>



<p class="wp-block-paragraph">This lets you dimension and constrain sketches efficiently and intuitively.</p>



<h3 class="wp-block-heading">System Options &gt; Display</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-display.png" alt="System Options, Display page" class="wp-image-3564" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-display.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-display-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-display-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-display-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="18" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Dynamic highlight from graphics view&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">This highlights an edge or face when you move the mouse cursor over it, before you click.</p>



<p class="wp-block-paragraph">The highlight is calculated in real time every time the cursor moves, so with large assemblies and other heavy models it can make the display <strong>stutter</strong>.</p>



<h3 class="wp-block-heading">System Options &gt; Performance</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-performance.png" alt="System Options, Performance page" class="wp-image-3565" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-performance.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-performance-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-performance-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-performance-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="19" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Verification on rebuild (enable advanced body checking)&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Every time the model is rebuilt, SOLIDWORKS runs an additional check for problems such as inconsistent geometry. You can catch model problems early, which helps you avoid designing on without noticing them.</p>



<p class="wp-block-paragraph">The time taken by that check is added to every rebuild.</p>



<ol start="20" class="wp-block-list">
<li><strong>[Your call] Set &#8220;Mate animation speed&#8221; to Fast</strong></li>
</ol>



<p class="wp-block-paragraph">When you apply a mate in an assembly, you can watch the animation of how the part moves into position. Because you can see whether it assembled in the intended orientation and position, you are less likely to miss a wrong mate.</p>



<p class="wp-block-paragraph">If the operation feels sluggish, turning the animation off may improve performance.</p>



<h3 class="wp-block-heading">System Options &gt; Assemblies</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-assemblies.png" alt="System Options, Assemblies page" class="wp-image-3566" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-assemblies.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-assemblies-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-assemblies-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-assemblies-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="21" class="wp-block-list">
<li><strong>Select &#8220;Move components by dragging&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Within the remaining degrees of freedom (the directions the part can still move), you can drag a part or subassembly with the mouse to move it.</p>



<p class="wp-block-paragraph">You do not have to call up a move command each time, so you can move parts intuitively.</p>



<ol start="22" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Update model graphics when saving files&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">This updates the model’s display data (graphics data) to the latest state whenever you save an assembly.</p>



<p class="wp-block-paragraph">If that display data is out of date, you may see the pre-change shape when you open the assembly in lightweight mode (a mode that loads only part of each component’s data so it opens faster), or in another viewer such as eDrawings.</p>



<p class="wp-block-paragraph">With this selected, the data is refreshed at every save, which helps prevent the mismatch of opening a file and finding an old shape. Refreshing the data at every save may add to the save time, so decide based on how large your assemblies are.</p>



<h3 class="wp-block-heading">System Options &gt; External References</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="668" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-external-references.png" alt="System Options, External References page" class="wp-image-3567" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-external-references.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-external-references-300x228.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-external-references-768x583.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-external-references-485x368.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="23" class="wp-block-list">
<li><strong>Clear &#8220;Don’t prompt to save read-only referenced documents (discard changes)&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">You may edit a file without noticing that it was opened read-only.</p>



<p class="wp-block-paragraph">With this option cleared, SOLIDWORKS warns you that the file is open read-only, which helps you avoid losing the edits you made.</p>



<ol start="24" class="wp-block-list">
<li><strong>Select &#8220;Update component names when documents are replaced&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you swap a part in an assembly with the Replace command, the name in the tree is updated to the new file name automatically.</p>



<ol start="25" class="wp-block-list">
<li><strong>Clear &#8220;Force referenced document to save to the same version as the parent document.&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Suppose you open and save an assembly made in an older version of SOLIDWORKS. With this option selected, all the parts and subassemblies in the assembly are converted to the current version and saved, including files you did not edit.</p>



<p class="wp-block-paragraph">With the option cleared, only the files you edited are saved in the current version, and the referenced files you did not touch stay in their original version.</p>



<p class="wp-block-paragraph">This can shorten save times. It also helps when you share files with someone who uses an older version of SOLIDWORKS: you will not accidentally upgrade a file to a version they cannot open.</p>



<h3 class="wp-block-heading">System Options &gt; FeatureManager</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="682" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-featuremanager.png" alt="System Options, FeatureManager page" class="wp-image-3568" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-featuremanager.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-featuremanager-300x232.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-featuremanager-768x595.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-featuremanager-485x376.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="26" class="wp-block-list">
<li><strong>Select &#8220;Scroll selected item into view&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you click a part or face in the 3D model, the matching item in the FeatureManager design tree (the list of parts and features on the left side of the screen) scrolls into view and is highlighted.</p>



<p class="wp-block-paragraph">In an assembly, you do not have to hunt for &#8220;which part in the tree is this?&#8221;</p>



<ol start="27" class="wp-block-list">
<li><strong>[Your call] Select &#8220;Dynamic highlight&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">When you move the mouse cursor over an edge, a face, or an item in the FeatureManager design tree, the target is highlighted before you click.</p>



<p class="wp-block-paragraph">It helps you avoid mistakes such as clicking and finding you selected a different face than you meant.</p>



<p class="wp-block-paragraph">However, the highlight is calculated in real time every time the cursor moves, so <strong>SOLIDWORKS can become sluggish</strong>.</p>



<h3 class="wp-block-heading">System Options &gt; View</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="690" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-view.png" alt="System Options, View page" class="wp-image-3687" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-view.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-view-300x235.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-view-768x602.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-view-485x380.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="28" class="wp-block-list">
<li><strong>Select &#8220;Reverse mouse wheel zoom direction&#8221;</strong></li>
</ol>



<p class="wp-block-paragraph">Turning the mouse wheel zooms a 3D model or a drawing in and out.</p>



<p class="wp-block-paragraph">The default zoom direction in SOLIDWORKS may feel opposite to what you are used to in other apps, such as Excel, so some people find it awkward.</p>



<p class="wp-block-paragraph">If you select this option, the wheel direction can match those apps, which makes it easier to use. (Which direction feels natural is a matter of habit, so skip this if the default suits you.)</p>



<h3 class="wp-block-heading">System Options &gt; Backup/Recover/Version</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="690" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-backup-recover.png" alt="System Options, Backup/Recover/Version page" class="wp-image-3688" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-backup-recover.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-backup-recover-300x235.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-backup-recover-768x602.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-backup-recover-485x380.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="29" class="wp-block-list">
<li><strong>Select &#8220;Save auto-recover information every:&#8221; and enter the interval you want</strong></li>
</ol>



<p class="wp-block-paragraph">When you work with several large files open, or run complex operations, SOLIDWORKS can crash or freeze.</p>



<p class="wp-block-paragraph">To protect the file you are editing in such cases, I recommend saving auto-recover information.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">Unfortunately, SOLIDWORKS can freeze or shut down unexpectedly.</p>



<p class="wp-block-paragraph">I set mine to 20 minutes, since I can live with redoing about that much work, including the mental cost.</p>
</div></div>



<p class="wp-block-paragraph">Each auto-save makes SOLIDWORKS slower for a moment, so do not set the interval too short.</p>



<p class="is-style-supplement-warning wp-block-paragraph">Even with auto-save enabled, there are cases where nothing is saved automatically.<br><strong>Saving as you edit</strong> is the best protection.</p>



<h3 class="wp-block-heading">System Options &gt; Messages/Errors/Warnings</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="880" height="682" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-messages-errors-warnings.png" alt="System Options, Messages/Errors/Warnings page" class="wp-image-3569" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-messages-errors-warnings.png 880w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-messages-errors-warnings-300x232.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-messages-errors-warnings-768x595.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/system-options-messages-errors-warnings-485x376.png 485w" sizes="auto, (max-width: 880px) 100vw, 880px" /></figure>



<ol start="30" class="wp-block-list">
<li><strong>Select &#8220;Remind me when a document has not been saved for:&#8221; and enter the time you want</strong></li>



<li><strong>Select &#8220;Automatically dismiss notifications after:&#8221; and enter the time you want</strong></li>
</ol>



<p class="wp-block-paragraph">If you keep editing a file and the time you entered passes without a save, a message prompting you to save appears at the lower right of the screen.</p>



<p class="wp-block-paragraph">This reminder should not cost as much as saving auto-recover information, so a shorter interval than the auto-save interval should be fine.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">The messages can feel a little annoying, but they keep you from forgetting to save, so I recommend setting them up.</p>



<p class="wp-block-paragraph">Honestly, they do not get in the way much.</p>
</div></div>



<h2 class="wp-block-heading">Bonus: Document Properties</h2>



<p class="wp-block-paragraph">Finally, here is a setting that helps prevent mistakes with overridden dimensions.</p>



<p class="wp-block-paragraph">Document Properties are set from the <strong>Document Properties</strong> tab of <strong>Tools &gt; Options</strong>. Open a file first, and then set the Document Properties.</p>



<ol start="32" class="wp-block-list">
<li><strong>Select the option that highlights overridden dimensions in a different color (found on the Dimensions page; available in SOLIDWORKS 2024 and later)</strong></li>
</ol>



<p class="wp-block-paragraph">Overridden dimensions (dimensions whose displayed value has been typed over instead of measured from the model) are shown in a different color. You can see at a glance which dimensions are temporarily or provisionally overridden, which helps you avoid unpleasant surprises.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">Used together with the System Options &gt; Colors settings, this makes changes even easier to spot.</p>
</div></div>



<h2 class="wp-block-heading">Summary</h2>



<p class="wp-block-paragraph">This article explained the SOLIDWORKS System Options, especially the settings that improve usability.</p>



<p class="wp-block-paragraph">Setting up your environment before you start real design work can reduce effort and help prevent mistakes.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray width_full l icon_red"><figure class="icon"><img decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">If you have recommended settings that I did not cover, I would be glad if you shared them in the comments.</p>
</div></div>



<p class="is-style-supplement-normal wp-block-paragraph">If you care more about the processing speed of SOLIDWORKS itself than about usability, see this article: <a href="https://sugitama-lab.tech/en/solidworks-performance-optimize/"><strong>SOLIDWORKS Performance Optimization: Settings to Make SOLIDWORKS Run Faster</strong></a></p>



<p class="wp-block-paragraph">&nbsp;</p>



<p class="wp-block-paragraph">Thank you for reading to the end.</p>
]]></content:encoded>
					
					<wfw:commentRss>https://sugitama-lab.tech/en/solidworks-system-options-usability/feed/</wfw:commentRss>
			<slash:comments>0</slash:comments>
		
		
		<post-id xmlns="com-wordpress:feed-additions:1">3690</post-id>	</item>
		<item>
		<title>SOLIDWORKS Mouse Gestures: How to Customize Them and My Recommended Setup</title>
		<link>https://sugitama-lab.tech/en/solidworks-mouse-gestures-setup/</link>
					<comments>https://sugitama-lab.tech/en/solidworks-mouse-gestures-setup/#respond</comments>
		
		<dc:creator><![CDATA[sugitama]]></dc:creator>
		<pubDate>Mon, 09 Nov 2026 22:41:59 +0000</pubDate>
				<category><![CDATA[Tips & Features]]></category>
		<category><![CDATA[for beginners]]></category>
		<category><![CDATA[initial settings]]></category>
		<category><![CDATA[makers]]></category>
		<category><![CDATA[students & education]]></category>
		<guid isPermaLink="false">https://sugitama-lab.tech/?p=3683</guid>

					<description><![CDATA[Mouse gestures put your most-used SOLIDWORKS commands under the cursor. Learn how to set them up, and see the 4-gesture setup I use for parts, assemblies, sketches, and drawings.]]></description>
										<content:encoded><![CDATA[
<p class="wp-block-paragraph">When you model and draw in SOLIDWORKS, I recommend getting to know <strong>mouse gestures</strong>.</p>



<p class="wp-block-paragraph">With mouse gestures, the cursor travels a much shorter distance to reach a command, so you spend less time reaching for toolbars. That may also take some load off the wrist that handles the mouse.</p>



<p class="wp-block-paragraph">Mouse gestures already work with the default settings. But if you put the commands <em>you</em> use most into them, they become far more useful.</p>



<p class="wp-block-paragraph">This article explains how to set up mouse gestures, and shows the setup I use myself.</p>



<p class="wp-block-paragraph">The setup itself takes only a few minutes.</p>



<p class="wp-block-paragraph">Let&#8217;s get started.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">What Are Mouse Gestures?</h2>



<p class="wp-block-paragraph">Mouse gestures are a feature that appears when you <strong>right-drag</strong> (hold the right mouse button and move the mouse) in the SOLIDWORKS graphics area, the large area where your model is displayed.</p>



<p class="wp-block-paragraph">A ring of command buttons (the <strong>mouse gesture guide</strong>) appears around the cursor. Just slide the cursor toward a button, and that command starts.</p>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="322" height="308" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-wheel-en.png" alt="Mouse gesture guide: a ring of command buttons appears around the cursor when you right-drag" class="wp-image-3679" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-wheel-en.png 322w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-wheel-en-300x287.png 300w" sizes="auto, (max-width: 322px) 100vw, 322px" /></figure>



<p class="wp-block-paragraph">With the default settings, the mouse gestures in a part or assembly look like the figure above.</p>



<p class="wp-block-paragraph">If you put your frequently used commands into mouse gestures, you no longer have to move the mouse all the way to the toolbar every time. That saves time.</p>



<p class="wp-block-paragraph">Mouse work also adds up over a day of design. Some people report wrist problems from heavy mouse use, and fewer long cursor movements may help. I do not know how much, but it could be a side benefit.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<p class="wp-block-paragraph">You can set mouse gestures separately for <strong>Part, Assembly, Sketch, and Drawing</strong>. (Part, Assembly, and Drawing are document types. Sketch is the mode you are in while editing a sketch.)</p>



<p class="wp-block-paragraph">This is because each of these has its own commands you use most. You might put Extruded Boss/Base in the part gestures, and Smart Dimension in the sketch gestures.</p>



<p class="wp-block-paragraph">To me, mouse gestures are one of the handiest features in SOLIDWORKS.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">How to Set Up Mouse Gestures</h2>



<p class="is-style-supplement-warning wp-block-paragraph">The images in this article are based on SOLIDWORKS for Makers (2022). Other versions can look a little different. For example, in SOLIDWORKS 2017 the dialog was laid out as a grid, and only 4 and 8 gestures were available.</p>



<h3 class="wp-block-heading">Open the Mouse Gestures Settings</h3>



<ol class="wp-block-list">
<li>Open any file in SOLIDWORKS.</li>



<li>Choose <strong>Tools &gt; Customize</strong>.</li>



<li>Click the <strong>Mouse Gestures</strong> tab. The mouse gesture guide window appears to the right of the dialog.</li>
</ol>



<p class="wp-block-paragraph">Here is what each setting does.</p>



<h5 class="wp-block-heading">1. Turn on mouse gestures</h5>



<p class="wp-block-paragraph">Select <strong>Enable mouse gestures</strong>. This turns the feature on. (It is probably already selected by default.)</p>



<h5 class="wp-block-heading">2. Choose the number of gestures</h5>



<p class="wp-block-paragraph">This sets how many commands are arranged around the ring. The default is four.</p>



<p class="wp-block-paragraph">You can choose from six layouts: 2 gestures (vertical), 2 gestures (horizontal), 3, 4, 8, and 12 gestures. The figure below shows how the commands are arranged in each one.</p>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="1506" height="1067" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en.png" alt="The mouse gesture guide layouts for 2 (vertical), 2 (horizontal), 3, 4, 8, and 12 gestures in Part, Sketch, Assembly, and Drawing" class="wp-image-3680" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en.png 1506w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en-300x213.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en-1024x726.png 1024w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en-768x544.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-layouts-en-485x344.png 485w" sizes="auto, (max-width: 1506px) 100vw, 1506px" /></figure>



<p class="wp-block-paragraph">The more gestures you use, the more commands you can reach. But it takes longer to get used to them, and you are more likely to pick the wrong one.</p>



<h5 class="wp-block-heading">3. Narrow the command list by category</h5>



<p class="wp-block-paragraph">The list of commands on the left shows every command available in SOLIDWORKS when the category is set to all commands.</p>



<p class="wp-block-paragraph">If there are too many commands and you cannot find the one you want, change the category (or use the search box). The list narrows down and becomes easier to scan.</p>



<h5 class="wp-block-heading">4. Drag a command onto the guide</h5>



<p class="wp-block-paragraph">From the list, <strong>drag</strong> the command you want and <strong>drop</strong> it on the position you want in the mouse gesture guide on the right. If you drop it on an empty position, the command is added. If you drop it on an occupied position, it replaces the command that was there.</p>



<p class="wp-block-paragraph">Do this for each of Part, Assembly, Sketch, and Drawing to build the layout you want.</p>



<h5 class="wp-block-heading">5. Click OK</h5>



<p class="wp-block-paragraph">Click <strong>OK</strong> to finish.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">My Recommended Mouse Gesture Setup</h2>



<p class="wp-block-paragraph">Here is the setup I use. If you are not sure which commands to assign, or you do not want to spend time deciding, feel free to copy it. If you already use mouse gestures, I hope it gives you some ideas for your own.</p>



<h3 class="wp-block-heading">I Recommend Starting with 4 Gestures</h3>



<p class="wp-block-paragraph">I recommend starting with <strong>4 gestures</strong>.</p>



<p class="wp-block-paragraph">In my opinion, four commands are enough to be useful, and the layout leaves room to grow. Two or three gestures feel a little limiting, while eight is a lot of positions to memorize.</p>



<p class="wp-block-paragraph">With four gestures, you learn the positions as you use them. Soon you can start a command before the guide even appears, and move quickly through modeling and sketching.</p>



<p class="wp-block-paragraph">Four gestures use only <strong>vertical and horizontal</strong> movements. Even if two gestures would be enough for you, setting up four costs little, and straight up, down, left, and right movements are easy to tell apart, so you are less likely to trigger the wrong one than with diagonal movements.</p>



<p class="wp-block-paragraph">If you later want more commands, you can move up to eight gestures, which adds the 45-degree diagonals. If you are already used to four gestures, the switch should go smoothly. (For that reason, I would not choose three gestures.)</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Here Is My Setup</h3>



<figure class="wp-block-image size-full"><img loading="lazy" decoding="async" width="502" height="532" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-recommended-en.png" alt="My recommended 4-gesture setup for Part, Sketch, Assembly, and Drawing" class="wp-image-3681" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-recommended-en.png 502w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-recommended-en-283x300.png 283w, https://sugitama-lab.tech/wp-content/uploads/2026/11/mouse-gesture-recommended-en-485x514.png 485w" sizes="auto, (max-width: 502px) 100vw, 502px" /></figure>



<p class="wp-block-paragraph">The command in each direction is listed below. (&#8593; means moving the cursor up, &#8595; down, &#8592; left, and &#8594; right.)</p>



<figure class="wp-block-table"><table class="has-fixed-layout"><thead><tr><th>Mode</th><th>&#8593; Up</th><th>&#8595; Down</th><th>&#8592; Left</th><th>&#8594; Right</th></tr></thead><tbody><tr><td><strong>Part</strong></td><td>Measure</td><td>Trimetric</td><td>Hole Wizard</td><td>Sketch</td></tr><tr><td><strong>Assembly</strong></td><td>Measure</td><td>Trimetric</td><td>Mate</td><td>Insert Components</td></tr><tr><td><strong>Drawing</strong></td><td>Smart Dimension</td><td>Zoom to Sheet</td><td>Hole Callout</td><td>Note</td></tr><tr><td><strong>Sketch</strong></td><td>Smart Dimension</td><td>Corner Rectangle</td><td>Line</td><td>Circle</td></tr></tbody></table></figure>



<p class="wp-block-paragraph">&nbsp;</p>



<p class="wp-block-paragraph">Here is my reasoning.</p>



<p class="wp-block-paragraph"><strong>Down in Part, Assembly, and Drawing</strong> is a view command: Trimetric (an angled 3D view) in a part or assembly, and Zoom to Sheet in a drawing. When I finish looking at one area in detail and want to move on to another, switching to a familiar view first makes it easier to see where to go next.</p>



<p class="wp-block-paragraph"><strong>Up</strong> is a dimension or measurement command in every mode. During design work I often check clearances and spaces between parts, so I assigned <strong>Measure</strong> and <strong>Smart Dimension</strong>.</p>



<p class="wp-block-paragraph">For the rest, I assigned commands I tend to use in each mode:</p>



<ul class="wp-block-list">
<li><strong>Part:</strong> Sketch and Hole Wizard</li>



<li><strong>Assembly:</strong> Insert Components and Mate</li>



<li><strong>Drawing:</strong> Hole Callout and Note</li>



<li><strong>Sketch:</strong> Line, Corner Rectangle, and Circle</li>
</ul>



<p class="wp-block-paragraph">I also tried to put similar functions in the same direction in every mode, so the gestures are easier to remember.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Summary</h2>



<p class="wp-block-paragraph">This article explained SOLIDWORKS mouse gestures: how to customize them, and the setup I recommend.</p>



<p class="wp-block-paragraph">Once you get used to mouse gestures, they can save you a lot of mouse travel in everyday SOLIDWORKS work. If you have not tried them yet, they are worth a few minutes.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<p class="wp-block-paragraph">Mouse gesture settings are also quite personal, and they vary from designer to designer.</p>



<p class="wp-block-paragraph">That is why I am curious about what other people have set up, and which commands they use.</p>



<p class="wp-block-paragraph">If you have a setup you like, I would love to hear about it in the comments.</p>



<p class="wp-block-paragraph">Thank you for reading to the end.</p>

]]></content:encoded>
					
					<wfw:commentRss>https://sugitama-lab.tech/en/solidworks-mouse-gestures-setup/feed/</wfw:commentRss>
			<slash:comments>0</slash:comments>
		
		
		<post-id xmlns="com-wordpress:feed-additions:1">3683</post-id>	</item>
		<item>
		<title>SOLIDWORKS File Management: Pitfalls to Avoid and How to Manage Your Files</title>
		<link>https://sugitama-lab.tech/en/solidworks-file-management-tips/</link>
					<comments>https://sugitama-lab.tech/en/solidworks-file-management-tips/#respond</comments>
		
		<dc:creator><![CDATA[sugitama]]></dc:creator>
		<pubDate>Mon, 09 Nov 2026 22:41:55 +0000</pubDate>
				<category><![CDATA[settings]]></category>
		<category><![CDATA[file management]]></category>
		<category><![CDATA[for beginners]]></category>
		<category><![CDATA[initial settings]]></category>
		<guid isPermaLink="false">https://sugitama-lab.tech/?p=3674</guid>

					<description><![CDATA[SOLIDWORKS files are quirky: rename or move one carelessly and your assemblies lose their links. Learn the pitfalls to avoid and how to manage your files safely.]]></description>
										<content:encoded><![CDATA[
<p class="wp-block-paragraph">If you use SOLIDWORKS, you probably appreciate how convenient it is as a CAD tool. But you have probably also run into the other side of it.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">SOLIDWORKS can be pretty quirky!</p>
</div></div>



<p class="wp-block-paragraph">Things do not always work the way you would expect. One of the clearest examples is <strong>file management</strong>.</p>



<p class="wp-block-paragraph">Maybe a file name was changed without you noticing, and an assembly then showed errors about missing references (broken links to its parts).</p>



<p class="wp-block-paragraph">Repairing files takes time and effort, so you want to prevent that kind of trouble whenever you can.</p>



<p class="wp-block-paragraph">This article explains the points to watch when you handle SOLIDWORKS files, and how to manage them.</p>



<p class="wp-block-paragraph">If you know the quirks of SOLIDWORKS files, you can avoid errors before they happen and save yourself a lot of rework.</p>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_ttl"><div class="box_title"><span class="span__box_title">Pitfalls to Watch For</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li>Once you save a file, do not rename it or move its folder (if you can help it).</li>



<li>Save the model file and its drawing file in the same folder, with the same name.</li>



<li>Use plain letters, numbers, hyphens, and underscores in file names.</li>



<li>A rename updates an assembly only if that assembly is open at the time.</li>



<li>Do not save files with the same name in different folders.</li>
</ul>
</div></div>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_ttl"><div class="box_title"><span class="span__box_title">How to Manage Your Files</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li>Do not rename or move SOLIDWORKS files in Windows File Explorer. Use SOLIDWORKS File Utilities instead.</li>



<li>Set rules for where to save files and how to name them.</li>
</ul>
</div></div>



<p class="wp-block-paragraph">If you work with SOLIDWORKS files without knowing these points, you may end up with a lot of errors and spend a lot of time fixing them.</p>



<p class="wp-block-paragraph">So if you are a beginner, I especially recommend reading to the end.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Pitfalls (Quirks) of SOLIDWORKS File Management</h2>



<p class="wp-block-paragraph">File management in SOLIDWORKS is very quirky.</p>



<p class="wp-block-paragraph">If you move folders or rename files without knowing this, repairing the data can take a lot of time, and in the worst case you may not be able to open the files at all.</p>



<p class="wp-block-paragraph">Let&#8217;s start with the quirks themselves.</p>



<h3 class="wp-block-heading">Once You Save a File, Do Not Rename It or Move Its Folder</h3>



<p class="wp-block-paragraph">After you save a SOLIDWORKS file, I recommend that you do not rename it, move it to another folder, or rename the folder.</p>



<p class="wp-block-paragraph">In SOLIDWORKS, you can insert other files into an assembly or a part file.</p>



<p class="wp-block-paragraph">For example, you can insert part files and other assemblies into an assembly. You can also insert other parts into a part.</p>



<p class="wp-block-paragraph">The inserted parts and assemblies are linked by their <strong>folder hierarchy and file names</strong>. (These links are called <strong>references</strong>.)</p>



<p class="wp-block-paragraph">If you change a file name or a folder name, the reference is broken.</p>



<p class="wp-block-paragraph">So unless you have a good reason, it is wise not to rename or move a file once you have saved it.</p>



<p class="wp-block-paragraph">The first time you save, check the save location and the file name carefully before you save.</p>



<p class="wp-block-paragraph">Save your files on the assumption that you will not rename or move them.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Save the Model File and the Drawing File in the Same Folder, with the Same Name</h3>



<p class="wp-block-paragraph">It is best to save the 3D model you created in SOLIDWORKS and the drawing file made from it <strong>in the same folder</strong>.</p>



<p class="wp-block-paragraph">This comes from the parent-child relationship between the files.</p>



<p class="wp-block-paragraph">In SOLIDWORKS, a drawing is created from a 3D model, so the 3D model is the <strong>parent</strong> and the drawing is the <strong>child</strong>.</p>



<p class="wp-block-paragraph">The drawing refers to the 3D model, so it is easy to open the model from the drawing. (In the FeatureManager design tree of the drawing, right-click the model under the drawing view and choose <strong>Open Part</strong> or <strong>Open Assembly</strong>.)</p>



<p class="wp-block-paragraph">You can also open the drawing from the 3D model (right-click the model and choose <strong>Open Drawing</strong>). Strictly speaking, though, this means &quot;you can open the drawing that has the <strong>same name</strong> and is in the <strong>same folder</strong> as the 3D model.&quot;</p>



<p class="wp-block-paragraph">If the drawing is saved under a different name than the 3D model, or in a different folder, you cannot open the drawing from the 3D model.</p>



<p class="wp-block-paragraph">So I recommend saving the model file and the drawing file in the same folder, and under the same name.</p>



<figure class="wp-block-image size-large"><img loading="lazy" decoding="async" width="1960" height="867" src="https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en.png" alt="Folder tree diagram showing a part file and its drawing file saved with the same name in the same folder" class="wp-image-3672" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en.png 1960w, https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en-300x133.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en-1024x453.png 1024w, https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en-768x340.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en-1536x679.png 1536w, https://sugitama-lab.tech/wp-content/uploads/2026/11/file-structure-same-name-en-485x215.png 485w" sizes="auto, (max-width: 1960px) 100vw, 1960px" /></figure>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">Save the model file and the drawing file under the same name, so that you can open the drawing from the 3D model.</p>
</div></div>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Use Plain Letters and Numbers in File Names</h3>



<p class="wp-block-paragraph">When you name files, it is best to stick to plain letters, numbers, hyphens, and underscores (basic ASCII characters).</p>



<p class="wp-block-paragraph">This was a problem in older versions of SOLIDWORKS: when a file name or folder name contained certain double-byte characters (such as Japanese characters), errors could occur, such as being unable to open the file.</p>



<p class="wp-block-paragraph">This has improved in recent versions, and you rarely see it now.</p>



<p class="wp-block-paragraph">However, many workplaces still use older versions of SOLIDWORKS, and you may need to hand files to suppliers or customers.</p>



<p class="wp-block-paragraph">It is an error that is easy to avoid, so I recommend using plain letters and numbers in file names.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">To avoid errors, stick to plain letters and numbers in file names.</p>
</div></div>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">A Rename Updates an Assembly Only If the Assembly Is Open</h3>



<p class="wp-block-paragraph">Suppose there is an assembly file named &quot;Assy-A&quot;, and one of its components is a part file named &quot;Part-B&quot;. Let&#8217;s say you want to rename &quot;Part-B&quot; to &quot;Part-C&quot;.</p>



<p class="wp-block-paragraph">In this case, the result is different depending on whether &quot;Assy-A&quot; is open in SOLIDWORKS or not.</p>



<h4 class="wp-block-heading">Example 1: Renaming while Assy-A is open</h4>



<p class="wp-block-paragraph">With &quot;Assy-A&quot; open in SOLIDWORKS, you open &quot;Part-B&quot; from the assembly (right-click it and choose <strong>Open Part</strong>) and rename it using <strong>File &gt; Save As</strong>. The component in Assy-A is automatically replaced from Part-B with Part-C.</p>



<p class="wp-block-paragraph">Renaming a component while Assy-A is open is reflected automatically. (Assy-A gets an asterisk (*) to show that it has been edited, so save Assy-A to keep the change.)</p>



<p class="wp-block-paragraph">In other words, <strong>the reference is kept</strong>.</p>



<h4 class="wp-block-heading">Example 2: Renaming without opening Assy-A</h4>



<p class="wp-block-paragraph">Suppose you open only &quot;Part-B&quot; in SOLIDWORKS, without opening &quot;Assy-A&quot;, and rename it with <strong>Save As</strong>. The component in Assy-A is still Part-B.</p>



<p class="wp-block-paragraph">When you open Assy-A in SOLIDWORKS later, a message saying that Part-B cannot be found appears.</p>



<p class="wp-block-paragraph">The reference inside Assy-A still points to Part-B, so <strong>the reference is not kept</strong>.</p>



<p class="wp-block-paragraph">If the model you want to rename is referenced by other models, whether the references are kept depends on whether the referencing models are open or closed.</p>



<p class="wp-block-paragraph">Decide before you save whether you want to keep the references or not, and choose the process accordingly.</p>



<p class="is-style-supplement-normal wp-block-paragraph">If no other file (assembly, part, or drawing) refers to a part, nothing else is affected, so you can rename it any way you like.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Do Not Save Files with the Same Name in Different Folders</h3>



<p class="wp-block-paragraph">In SOLIDWORKS, avoid saving files under the same name, even when they are in different folders.</p>



<p class="wp-block-paragraph">When you create a design variant, you may build another model from a base 3D model.</p>



<p class="wp-block-paragraph">One way is to keep the file name and just change the folder you save to, but this is <strong>not recommended</strong>.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">When the file names are the same, a file from the wrong folder often gets loaded by accident.</p>



<p class="wp-block-paragraph">You lose track of which one you are editing, and that is how trouble starts.</p>
</div></div>



<p class="wp-block-paragraph">When you create a variant model, always change the file name when you save.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">How to Manage SOLIDWORKS Files</h2>



<p class="wp-block-paragraph">As described above, SOLIDWORKS files are very quirky.</p>



<p class="wp-block-paragraph">If you keep moving folders and renaming files without thinking, you may reach a point where you cannot repair the models.</p>



<p class="wp-block-paragraph">Still, there will be times when you need to move or rename files.</p>



<p class="wp-block-paragraph">Here is how to manage SOLIDWORKS files properly. Managing files this way helps you prevent trouble and errors.</p>



<h3 class="wp-block-heading">Use SOLIDWORKS File Utilities When You Rename or Move Files</h3>



<p class="wp-block-paragraph">When you handle SOLIDWORKS files, do not rename or move them in Windows File Explorer.</p>



<p class="wp-block-paragraph">Use <strong>SOLIDWORKS File Utilities</strong> instead. It lets you rename, replace, and move SOLIDWORKS files while it tries to keep the references between them. This is exactly the situation in Example 2 above.</p>



<p class="wp-block-paragraph">You use it from the right-click menu in File Explorer: right-click a SOLIDWORKS file, choose <strong>SOLIDWORKS</strong>, pick a File Utilities command such as <strong>Rename</strong> or <strong>Move</strong>, and enter the new name or location. (On Windows 11, you may need to select <strong>Show more options</strong> first. If the menu is missing, File Utilities may not be installed, and you can add it with the SOLIDWORKS Installation Manager.)</p>



<p class="is-style-supplement-normal wp-block-paragraph">File Utilities replaced <strong>SOLIDWORKS Explorer</strong>, a separate file management application that was retired in SOLIDWORKS 2020. If you find older articles about SOLIDWORKS Explorer, use File Utilities instead (unless you still use SOLIDWORKS 2019 or earlier). See <a href="https://help.solidworks.com/2020/english/WhatsNew/c_explorer_replaced_by_utilities.htm" target="_blank" rel="noreferrer noopener">SOLIDWORKS Explorer replaced by SOLIDWORKS File Utilities</a> and <a href="https://help.solidworks.com/2025/english/SolidWorks/sldworks/c_solidworks_file_utilities.htm" target="_blank" rel="noreferrer noopener">SOLIDWORKS File Utilities</a> in the SOLIDWORKS Help.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Set Rules for Where to Save Files and How to Name Them</h3>



<p class="wp-block-paragraph">As I said before, it is best to save SOLIDWORKS files on the assumption that you will not rename them or move their folders.</p>



<p class="wp-block-paragraph">You can rename or move them afterward with File Utilities, but that takes time and effort.</p>



<p class="wp-block-paragraph">To avoid unnecessary work, I recommend setting clear rules for saving files.</p>



<p class="wp-block-paragraph">For example: &quot;Name files as <strong>ProjectName_PartName_RevisionNumber</strong>,&quot; or &quot;Save part files in a folder hierarchy of <strong>project name &gt; assembly name &gt; part</strong>.&quot; (If you put the revision number in the file name, every new revision means a rename, which goes against the first rule above. Think about whether it belongs in the name.)</p>



<p class="wp-block-paragraph">It is best to choose file names and a folder hierarchy that let other people understand what each part or assembly is just by looking at the names.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Summary</h2>



<p class="wp-block-paragraph">This article explained the points to watch in SOLIDWORKS file management, and how to manage files.</p>



<p class="wp-block-paragraph">Here is the summary of SOLIDWORKS file management.</p>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_simple"><div class="box_title"><span class="span__box_title">SOLIDWORKS File Management at a Glance</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li>Once you save a file, do not rename it or move its folder (if you can help it).</li>



<li>Save the model data and the drawing data in the same folder, with the same name.</li>



<li>Use plain letters, numbers, hyphens, and underscores in file names.</li>



<li>A rename updates an assembly only if that assembly is open at the time.</li>



<li>Do not rename or move files in File Explorer. Use SOLIDWORKS File Utilities.</li>



<li>Set rules for where to save files and how to name them.</li>
</ul>
</div></div>



<p class="wp-block-paragraph">If you understand the quirks of SOLIDWORKS files, you can manage them correctly.</p>



<p class="wp-block-paragraph">Steer clear of preventable errors and trouble, and manage your files efficiently.</p>



<p class="wp-block-paragraph">Thank you for reading to the end.</p>

]]></content:encoded>
					
					<wfw:commentRss>https://sugitama-lab.tech/en/solidworks-file-management-tips/feed/</wfw:commentRss>
			<slash:comments>0</slash:comments>
		
		
		<post-id xmlns="com-wordpress:feed-additions:1">3674</post-id>	</item>
		<item>
		<title>SOLIDWORKS Templates: How to Create a Custom Document Template and What to Set Up</title>
		<link>https://sugitama-lab.tech/en/solidworks-document-template-guide/</link>
					<comments>https://sugitama-lab.tech/en/solidworks-document-template-guide/#respond</comments>
		
		<dc:creator><![CDATA[sugitama]]></dc:creator>
		<pubDate>Mon, 09 Nov 2026 22:41:53 +0000</pubDate>
				<category><![CDATA[settings]]></category>
		<category><![CDATA[for beginners]]></category>
		<category><![CDATA[initial settings]]></category>
		<category><![CDATA[speed & performance]]></category>
		<guid isPermaLink="false">https://sugitama-lab.tech/?p=3670</guid>

					<description><![CDATA[Stop repeating the same settings in every new file. Learn how to create, save, and use a SOLIDWORKS document template, and which settings are worth building into it.]]></description>
										<content:encoded><![CDATA[
<p class="wp-block-paragraph">Every time you create a new file in SOLIDWORKS, do you find yourself repeating the same settings changes?</p>



<p class="wp-block-paragraph">If you change the units every time, or fix the drawing border every time, that is a big loss of time.</p>



<p class="wp-block-paragraph">If you want to work efficiently in SOLIDWORKS, I strongly recommend setting up your own <strong>document template</strong>.</p>



<p class="wp-block-paragraph">The default templates are designed to be general-purpose. For production work, they often lack something you need, or do not match your company&#8217;s standards.</p>



<p class="wp-block-paragraph">Customizing them gives you these benefits.</p>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_ttl"><div class="box_title"><span class="span__box_title">What You Gain from an Optimized Template</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li><strong>Less time spent</strong>: You no longer have to change the same settings each time.</li>



<li><strong>Fewer mistakes</strong>: You avoid errors such as the wrong unit system or the wrong drafting standard.</li>



<li><strong>Consistent quality</strong>: A whole team or company can share the same drawing appearance and properties.</li>
</ul>
</div></div>



<p class="wp-block-paragraph">This article explains how to create and use a SOLIDWORKS document template, and which settings I recommend putting in it, from the viewpoint of everyday work.</p>



<p class="wp-block-paragraph">Customizing your templates is an easy way to improve your efficiency.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">What Is a SOLIDWORKS Template?</h2>



<p class="wp-block-paragraph">SOLIDWORKS has several kinds of templates.</p>



<p class="wp-block-paragraph">This article focuses on the <strong>document template</strong>.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">The document template is the main one.</p>



<p class="wp-block-paragraph">There are other kinds of templates too, such as the bill of materials template.</p>
</div></div>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_ttl"><div class="box_title"><span class="span__box_title">What You Can Set in a Document Template</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li><strong>Document Properties</strong>: mainly the drafting standard, the unit system, and the dimension style</li>



<li><strong>File properties</strong>: the items you want to store as information about the model</li>



<li><strong>Display state of the 3D model</strong>: the background brightness, the display style, the items shown in the FeatureManager design tree, and so on</li>



<li><strong>Drawing border and line styles</strong> for drawings</li>
</ul>
</div></div>



<p class="wp-block-paragraph">If you set up your document template well, you can unify the look of your models and drawings the way you or your company like.</p>



<p class="wp-block-paragraph">It also makes your work more efficient, both in design and in the steps after design.</p>



<p class="wp-block-paragraph">For example, a common drafting standard, unit system, and drawing border are essential when you handle drawings. A common font, line style, and arrow size also change how easy a drawing is to read.</p>



<p class="wp-block-paragraph">Whether the background is light or dark also affects how tired your eyes get while you model.</p>



<p class="wp-block-paragraph">You need to set up a document template separately for each of the three file types: <strong>part, assembly, and drawing</strong>.</p>



<p class="wp-block-paragraph">In addition, if you need four drawing sizes, for example A1, A2, A3, and A4, you need to create four drawing templates.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">So you need two model templates and four drawing templates (for A1 to A4).</p>



<p class="wp-block-paragraph">It is not difficult, but it takes a little effort to make them.</p>
</div></div>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Document Properties vs. System Options</h2>



<p class="wp-block-paragraph">SOLIDWORKS has another kind of setting: <strong>System Options</strong>.</p>



<p class="wp-block-paragraph">Let&#8217;s get a rough idea of how Document Properties and System Options differ.</p>



<div class="wp-block-stk-plugin-cbox cbox intitle is-style-site_color type_simple"><div class="box_title"><span class="span__box_title">The Difference at a Glance</span></div><div class="cboxcomment">
<ul class="wp-block-list">
<li><strong>System Options</strong><br>These apply to all files, both existing and new. They are stored in the registry, not in the file. You can think of them as settings for each user, each device, or each PC.</li>



<li><strong>Document Properties</strong><br>These are stored in the file. Even on a PC with different settings, the file is used and displayed under the same conditions. The unit system or the dimension display style does not change because of a PC&#8217;s settings.</li>
</ul>
</div></div>



<p class="wp-block-paragraph">Because a template stores Document Properties, the settings you build into it travel with every file you create from it.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">How to Save and Use a Document Template</h2>



<p class="wp-block-paragraph">Let&#8217;s look at how to make a document template.</p>



<p class="wp-block-paragraph">You do not start from zero. You customize one of the default SOLIDWORKS templates for your own use.</p>



<p class="wp-block-paragraph">The steps below use a part template as an example.</p>



<h3 class="wp-block-heading">Save a Template</h3>



<ol class="wp-block-list">
<li>Click <strong>New</strong> and create a new part from any existing part template (the default one is fine).</li>



<li>Set the items you want in <strong>Document Properties</strong>. If there are other settings you want, such as file properties or the display state, set those too.</li>



<li>As an example, let&#8217;s change the drafting standard. Click <strong>Tools &gt; Options</strong> and open the <strong>Document Properties</strong> tab.</li>
</ol>



<figure class="wp-block-image size-large"><img loading="lazy" decoding="async" width="1021" height="339" src="https://sugitama-lab.tech/wp-content/uploads/2026/10/perf-sysopt-open-menu.png" alt="Tools menu in SOLIDWORKS with the Options command highlighted" class="wp-image-3224" srcset="https://sugitama-lab.tech/wp-content/uploads/2026/10/perf-sysopt-open-menu.png 1021w, https://sugitama-lab.tech/wp-content/uploads/2026/10/perf-sysopt-open-menu-300x100.png 300w, https://sugitama-lab.tech/wp-content/uploads/2026/10/perf-sysopt-open-menu-768x255.png 768w, https://sugitama-lab.tech/wp-content/uploads/2026/10/perf-sysopt-open-menu-485x161.png 485w" sizes="auto, (max-width: 1021px) 100vw, 1021px" /></figure>



<ol start="4" class="wp-block-list">
<li>Go to <strong>Drafting</strong> and change <strong>Overall drafting standard</strong> to the one you use (for example, ISO, ANSI, DIN, or JIS). Then click <strong>OK</strong> to close the window.</li>



<li>Click <strong>File &gt; Save As</strong>. Set <strong>Save as type</strong> to <strong>Part Templates (*.prtdot)</strong>.</li>



<li>Browse to a folder of your own (create one first if you need to), and save the file there.</li>
</ol>



<p class="wp-block-paragraph">Give the folder a name that tells you at a glance what kind of templates are inside. I explain why in the next section.</p>



<p class="wp-block-paragraph">In this example, I saved a document template file named <strong>Sugitama_Parts.prtdot</strong> in a folder named <strong>sugitama_template</strong>.</p>



<p class="is-style-supplement-normal wp-block-paragraph">Assembly templates use <strong>Assembly Templates (*.asmdot)</strong> and drawing templates use <strong>Drawing Templates (*.drwdot)</strong> as the file type. SOLIDWORKS may suggest its default template folder when you choose a template type. It is safer to keep your own templates in a folder outside the SOLIDWORKS installation folder, so that an upgrade or reinstall cannot overwrite them.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Use the Template</h3>



<p class="wp-block-paragraph">After you save a template, make it available in SOLIDWORKS. To use a template you created, you need to change a System Option.</p>



<ol class="wp-block-list">
<li>Click <strong>Tools &gt; Options</strong> to open the System Options.</li>



<li>On the <strong>System Options</strong> tab, select <strong>File Locations</strong>.</li>



<li>Make sure <strong>Show folders for</strong> is set to <strong>Document Templates</strong>, and click <strong>Add</strong>.</li>



<li>In the folder window that opens, select the folder that holds your templates and click <strong>Select Folder</strong>.</li>



<li>Check that the folder you selected is now in the list, and click <strong>OK</strong>.</li>



<li>Click <strong>File &gt; New</strong>. If the dialog is not already in the Advanced view, switch to <strong>Advanced</strong>.</li>
</ol>



<p class="wp-block-paragraph">A new tab named <strong>sugitama_template</strong> appears, and the template <strong>Sugitama_Parts</strong> is now available.</p>



<p class="is-style-supplement-normal wp-block-paragraph">The name of the folder becomes the name of the tab. That is why I suggest giving the folder a name you can recognize at a glance. Make sure the folder contains at least one template file, or the tab may not appear.</p>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Recommended Settings for Your Template</h2>



<p class="wp-block-paragraph">Here are the settings that I think are useful to build into a template.</p>



<h3 class="wp-block-heading">Settings for Parts and Assemblies</h3>



<p class="wp-block-paragraph">First, the settings for part templates and assembly templates.</p>



<p class="wp-block-paragraph">These settings cover the information the model itself keeps, and the settings that make modeling easier.</p>



<h4 class="wp-block-heading">1. Document Properties</h4>



<p class="wp-block-paragraph">Check the following items in Document Properties.</p>



<ul class="wp-block-list">
<li><strong>Drafting standard</strong>: Choose the standard that your company and your customers use, such as ISO, ANSI, DIN, or JIS.</li>



<li><strong>Units</strong>: Millimeters, kilograms, and seconds are a practical choice if you work in metric. (To combine millimeters with kilograms, choose <strong>Custom</strong> on the <strong>Units</strong> page.)</li>



<li><strong>Font</strong>: Choose whichever font you like, but pick one that is installed on Windows by default. If you send the data to a customer who does not have your font, it will not display correctly.</li>



<li><strong>Image Quality</strong>: This controls how smooth curves look. A finer setting lowers performance, so be careful.</li>
</ul>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">Some companies specify the arrow type, the font, and the size.</p>



<p class="wp-block-paragraph">In that case, set these to match your internal standard.</p>
</div></div>



<h4 class="wp-block-heading">2. Add Reference Axes</h4>



<p class="wp-block-paragraph">If you insert reference axes in the template (<strong>Insert &gt; Reference Geometry &gt; Axis</strong>), modeling and drawing become more efficient.</p>



<p class="wp-block-paragraph">With axes in place, you can dimension from an axis or add relations to it while you model, which makes modeling easier.</p>



<p class="wp-block-paragraph">You can also show the axes on the drawing, so you do not need to insert a centerline each time.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">This is not a required setting, but it is a good one to add because it saves work.</p>
</div></div>



<p class="wp-block-paragraph">After you create the axes, turn on the axis display (<strong>View &gt; Hide/Show &gt; Axes</strong>).</p>



<p class="wp-block-paragraph">If you forget, the axes you made stay hidden.</p>



<h4 class="wp-block-heading">3. File Properties (Custom Properties)</h4>



<p class="wp-block-paragraph">In SOLIDWORKS, you can register file properties (<strong>File &gt; Properties</strong>) for both model files and drawing files.</p>



<p class="wp-block-paragraph">The information you enter in the model&#8217;s properties can be read into the title block of the drawing automatically, and it can also be used to create a bill of materials automatically.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">In SOLIDWORKS, the model and the drawing are linked, and the model is the parent. (The drawing is created by referring to the model.)</p>



<p class="wp-block-paragraph">If you put the information in the model, it carries over to the drawing automatically.</p>
</div></div>



<p class="wp-block-paragraph">Pick the items you want to register as properties, and set them up in the template.</p>



<p class="wp-block-paragraph">Typical basic management items include the <strong>drawing number, model name, designer, drafter, and creation date</strong>. It also helps to add the items needed for manufacturing, such as <strong>material, heat treatment, surface treatment, and quantity</strong>.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">If you need other items for management, add them as needed.</p>



<p class="wp-block-paragraph">Filling these in makes drawing creation smoother.</p>
</div></div>



<p class="wp-block-paragraph">Set up the model file&#8217;s properties so that you can use them in drawings.</p>



<p class="wp-block-paragraph">The properties of a drawing file usually have no particular use, so you do not need to set them in the template.</p>



<h4 class="wp-block-heading">4. View Settings</h4>



<p class="wp-block-paragraph">You look at the screen for a long time while you design. Set up the display so that it is as easy on your eyes as possible.</p>



<p class="wp-block-paragraph">This is purely a matter of taste. I use the following settings.</p>



<ul class="wp-block-list">
<li>Display style: <strong>Shaded With Edges</strong></li>



<li>Background: I leave it at the default</li>



<li>Floor reflection and floor shadow: turned off</li>
</ul>



<p class="wp-block-paragraph">Nothing unusual. My display is close to the default.</p>



<h4 class="wp-block-heading">5. FeatureManager Design Tree Display</h4>



<p class="wp-block-paragraph">A cluttered FeatureManager design tree is hard to read, so tidy up how it is displayed.</p>



<div class="wp-block-stk-plugin-voicecomment voice comment_gray l icon_red"><figure class="icon"><img loading="lazy" decoding="async" class="voice_icon__img" src="https://sugitama-lab.tech/wp-content/uploads/2021/12/illust_MEGANE_prf.png" width="100" height="100" alt=""/><figcaption class="avatar-name name">sugitama</figcaption></figure><div class="voicecomment">
<p class="wp-block-paragraph">If each part also shows its configuration and display state, the tree gets cluttered.</p>



<p class="wp-block-paragraph">If a part has only one configuration, hide those names and the tree becomes clean and easy to read.</p>
</div></div>



<p class="wp-block-paragraph">&nbsp;</p>



<h3 class="wp-block-heading">Settings for Drawings</h3>



<h4 class="wp-block-heading">1. Drawing Border (Sheet Format)</h4>



<p class="wp-block-paragraph">Set up the drawing border that you use on your drawings.</p>



<p class="wp-block-paragraph">The border and the title block together are called the <strong>sheet format</strong>. You need one for each drawing size you use. Use the paper sizes your company uses, for example A1 to A4 in ISO, or A to E in ANSI.</p>



<p class="wp-block-paragraph">To edit the border, right-click inside it and select <strong>Edit Sheet Format</strong>.</p>



<h4 class="wp-block-heading">2. Line Styles</h4>



<p class="wp-block-paragraph">The basic line styles are available by default. If you want to use a special line style all the time, it is a good idea to set it up in the template.</p>



<p class="wp-block-paragraph">For example, I often use these two:</p>



<ul class="wp-block-list">
<li>A line style that does not print, for design notes that I want to write on the drawing but not print</li>



<li>A color-coded line style that makes revised areas stand out</li>
</ul>



<p class="wp-block-paragraph">&nbsp;</p>



<h2 class="wp-block-heading">Summary</h2>



<p class="wp-block-paragraph">This article explained how to set up and use a document template, and the settings I recommend building into it.</p>



<p class="wp-block-paragraph">As you work with your template, you will find more and more things you want to add.</p>



<p class="wp-block-paragraph">Do not try to do everything at once. Update the template as you go, and you will build one that is easy to use.</p>



<p class="wp-block-paragraph">You can also create templates for specific situations, such as one for sheet metal parts, one for machined parts, and one for large assemblies.</p>



<p class="wp-block-paragraph">I hope a template tailored to your work makes SOLIDWORKS more comfortable to use.</p>



<p class="wp-block-paragraph">Thank you for reading to the end.</p>

]]></content:encoded>
					
					<wfw:commentRss>https://sugitama-lab.tech/en/solidworks-document-template-guide/feed/</wfw:commentRss>
			<slash:comments>0</slash:comments>
		
		
		<post-id xmlns="com-wordpress:feed-additions:1">3670</post-id>	</item>
	</channel>
</rss>
